Showing posts with label gardena. Show all posts
Showing posts with label gardena. Show all posts

Friday, 20 April 2018

Replacing the R40Li / 1200R / Automower Battery (Pictures and Steps)

As regular readers will know, our trusty Gardena R40Li has just entered service in its fifth season!

Also known variously as the Flymo 1200R, or Husqvarna Automower, this model was one of the first automatic robotic lawn mowers on the market, and still stacks up reasonably well against the competition.

However, after 2649 hours (see right), the battery had started to fail. The symptoms were fairly obvious:
  • Frequently returning to the base after only a few minutes;
  • Stopping cutting on manual, when battery showing half full.

In fact, some of the symptoms started towards the end of last season, but a couple of refreshes seemed to (temporarily) help. For this season, though, I decided to bite the bullet and replace the battery.

Over the intervening years, the poor mower has become a bit encrusted with old grass.

This is my own fault, as detailed in my rubber damper pictures and repairs article: I don't take as much care over cleaning as I should.

Luckily the battery compartment cover is easy to find; it sits between the rear wheel (bottom) and spinning plate that holds the three blades (top).

After a bit of scraping to reveal the screws (right), it becomes obvious why the instructions say to drop the cutting disc as low as possible.

Even though (as can be seen in the photo), the screw heads are accessible through the holes, once released, the cover needs to be lifted and slid out.

This is much easier to do if you first drop the spinning disc to it's lowest position, or minimum height, if you prefer.

The screws are, again T20 Torx, which ought to be familiar to anyone who has tried dismantling the auto mower already.

Once removed, the compartment cover reveals three things.

Firstly, there's the battery itself, complete with velcro tab to pull it out of it's moulded compartment.

Secondly, there's the USB port on the left, which I had not previously been aware of, but which I'm guessing would theoretically allow you to mod the mower.

A quick visit to the Gardena site reveals that for the Sileno and Sileno+ models at least, there is also a software update available. The download page redirects to Husqvarna and prompts to install an application, check the connected mower and update the firmware.

Something for a future post.

Meanwhile, the third thing to note is that it remains, despite external appearances, incredibly clean inside the battery compartment.


This is a testament to the rubber seals. Seals which, unlike the rubber dampers, stand up to the constant abuse.


On the left hand side of the page, there are the two batteries.

The one at the bottom is the new one, purchased on Amazon (see "r40li battery"). There were several to choose from.

Bang in the middle of the range of prices, was the one that I eventually bought, made by VHBW, apparently, and rated more or less at the same power as the original.

At the top end of the scale, costing over £100 is the a replacement made by Husqvarna; having read some reviews of the VBHW, I decided that it was worth the "risk".

At the lower end is a replacement at around £45, which just felt a little too cheap -- but I should point out I have only gut feeling to go on, and no basis of any other informed opinion!

I'd give it a shot, if I hand't been an early adopter of the robot mower revolution, and spent top whack for my trusty R40Li. If anyone has tried the cheaper batteries, or can convince me that they're not going to damage my 'bot, let me know.


The last step is just to drop the battery into place, wonder for a last time what that USB socket could be for, and screw the lid back on.

Care is needed to plug the battery into place, as the connector is a tight fit, but other than that, the replacement itself is an incredibly easy job.

The mower reported that the battery was about half full, but it returned to base quite quickly. Perhaps it should have been charged first.

However, the subsequent mowing period was substantially longer than with the old battery, which is a good sign. Only time will tell if the new battery performs as well as the original - over 2500 hours of mowing in a 5 year period seems like a pretty hard act to follow!

Previous articles on R40Li maintenance:


Friday, 2 June 2017

Flymo Robotic Lawnmower 1200R Review: Price, Setup, Maintenance and Tuning Advice

The Flymo 1200R robotic lawnmower is based on the Husqvarna Automower design, also used for the very popular Gardena R40Li. This isn't surprising, since Flymo and Gardena are both part of the Husqvarna group, whose Automower was arguably the first mass market automatic robot lawn mower.

With such an impressive pedigree, you'd expect something special, and you would be right.

Or, half right.

Flymo 1200R Price


Let's start with the price.

Currently (June 2017), the Flymo 1200R is priced at a very, very, competitive £599, via Amazon's UK site.

For those who are still reading, my own Gardena R40Li which is identical (except for the colour) cost over 1200 EUR. The Flymo 1200R went on sale at just under £1000, and although the design might come across as a bit dated (more on that later) it's proven to be very reliable.

Installing the Flymo 1200R


All robotic lawn mowers require the installation of a perimeter wire to stop the mower from cutting anything other than the lawn.

There are exceptions, but these are rare, and generally use training or GPS which are both pretty fiddly to set up.

The 1200R is easy to set up, if a little time-consuming. All you need to do is choose a spot for the base station, a location for the return wire, and lay the wire all around the mowing area. You even get a little ruler in the box to help you gauge the distance from the flower bed or path to the perimeter wire.

Online opinions vary as to whether you should actually physically bury the wire, but I'd caution against it. It grows over really quickly (a matter of weeks), and leaving it exposed lets you troubleshoot the installation if need be.

Once installed, you can then set up the cutting schedule, and other parameters (like the PIN) using the LCD screen and simple menu system. Actually, it's lucky that it is a simple menu, because the screen makes setting up the brain harder than it was to set up the rest!

Flymo 1200R Wheels


Where I also have a bit of beef is in the wheels.

Before taking the Flymo to market, I just wish they'd replaced those rubber band treads with solid plastic wheels. On rugged ground, they tend to wear out and drop off; this isn't as dire as it sounds, because replacing the wheels is incredibly easy.

But, it's one of those small things that niggles. Eventually, you know that you're going to have to replace the wheels, and you get into the habit of checking for wear and tear to try and prolong their life a bit.

Like the blades.

Flymo 1200R Blades


The blades give a great cutting result, but they're wafer thin.

There are three of them, and they spin freely to clip and mulch, so that a fine mist of grass ends floats down onto the lawn to fertilise it.

We've noticed the difference, but I've also started walking around the lawn from time to time and removing anything that might damage the blades, because easy as they are to replace, they can become expensive.

Still, that's the case with all robotic mowers in this price bracket. Luckily, too, since it's a popular design, numerous suppliers have popped up to supply unbranded aftermarket blades for Flymo, Gardena and Husqvarna mowers.

Flymo 1200R Battery


A robotic lawnmower lives and dies on its battery.

The Robin, for example, has a very low battery capacity. It's a very low cost mower, and takes a whopping 18 hours to recharge which means that its use is limited to small gardens.

Not so, the Flymo. It's got a great battery. It cuts for ages, and recharges quickly.

According to the manual it has a 2-3 year life span, but I have to say that we've gone sailing past that and don't see any visible change in performance.

Of course, we do overwinter the mower, and empty the battery frequently by letting it run around in a zone with no charging station, which may have an effect, but the battery shows little sign of needing replacing.

(And, if it ever does need replacing, it's easy to do. I checked!)

So, let's round up the good and bad of the Flymo 1200R:

Pros:

  • Value for money
  • Cutting quality
  • Robust build


Cons:

  • Tiny LCD screen
  • No phone link, app, or GPS
  • Rubber wheels


Features:

  • Mulching action
  • Audible alarm & PIN code
  • Super-silent operation
  • Collision detection


The conclusion, however, is the important bit. Would I buy it again? Yes. Not at the original price, because there are better robotic lawnmowers for around £1000. But at the current Flymo 1200R price, I'd snap it up in an instant.

Thursday, 20 October 2016

The Gardena R40Li Bumps Up Against A Problem...

So, having swapped out the rubber-tread wheels for nice, new shiny plastic ones (see: And Then, The Wheels Came Off!) the next bits that have failed are the two rear rubber dampers. These are going to need replacing, but first, let's take a moment to look at the symptoms and probable cause.

Before we do that, I'd encourage anyone that has the Gardena r40Li, Flymo 1200R or Husqvarna 305 to download the following exploded parts diagram from the Gardena web site:


And, whilst you're perusing it, and probably going "Ah, that's what that bit is!" at the same time, remember that we've had the r40Li since 2013, and this is only the second repair that we've had to do. Yes, I've changed the blades a couple of times per season -- thanks to the kids, the grass is littered with twigs -- but this is only the second major bit of work I've had to do.

This is despite the fact that I'm not the best at cleaning, or winterising the robot mower, which is where I suspect the cause of the current problems lie.

The Odd Symptoms of Bumper Failure


On the face of it, I should have realised straight away that something was amiss.

The mower would stop, mid-mow, for no reason, and then reverse. Then, it would turn and head off  in a direction, before stopping again, reversing, turning and trying to get going in a number of different directions before giving up.

Having turned itself off, a restart listed a "collision detection failure" a few times, before I twigged that maybe this wasn't simply a question of the mower getting stuck in a corner.

So, I picked it up.

When I did so, grasping the cover, including bumpers -- look at the diagram, p.13 -- and the chassis listed alarmingly. Normally it bobs around, suspended, as I now know, on four rubber dampers, that give it flexibility and allow for the bumper to detect collisions.

Now, with one broken, it registers a permanent list to one side, and the inevitable bumper failure with it.

What Caused the Rubber to Perish?


Both the rear dampers have perished. Possible causes that spring to mind are:
  • snails (and I'm not kidding: they eat the post!);
  • cold (changes in temperature attacks rubber like nothing else);
  • bumping into objects.
That last one is pertinent, as although the perimeter wire went in three years ago, we're still moving it around to get the best edge cutting possible. Thus, the mower spends a lot of time bumping into stone edges because the perimeter wire is just a little too close to the coping stones...

On the other hand, the amount of dead grass that I pulled out also hints that maybe that also had something to do with it.

Either way, my advice would be to:
  • clean,
  • winterise,
  • avoid snails,
  • place the perimeter wire a good distance away from any coping stones...
For readers with the same issue, the parts are numbers 574 46 91-02, and they cost around 7.50 EUR each plus delivery. Much less than the wheels; and I'll let you know how I get on swapping them out with the damaged ones.

The verdict? Still recommended!

Thursday, 17 September 2015

...And Then the Wheels Came Off!

It sounds like the punchline to a bad joke, but what do you do when the wheels come off your Gardena robotic lawnmower? The answer is simple, if a little long-winded: go back to the retailer and ask them to order new ones...

The Problem

The Gardena 40Li, Flymo 1200R, and Husqvarna 305 all look remarkably similar. In fact, I'd put money on the fact that they're all made by the same company, to the same design, which I'm fairly confident is Husqvarna itself.

To my knowledge, all of these share the same kind of wheels: a plastic hub and a rubber tread.

And here's the problem. After nearly 2 years of unbroken service (aside from over-wintering), my Gardena 40Li's wheels have come off.

Actually, it's just the rubber tread that has become worn out, and I found it lying on the damp lawn, with the poor mower comically pirouetting with one tread-less wheel being dragged around by the other, rubberised one.

The solution ought to have been simple -- in this day and age, surely it's possible to order Husqvarna parts online? Unfortunately, it proved to be a bit more tricky than I'd thought.

Out With the Old Wheels

Without the rubber tyres, not only can the mower not mow efficiently, but it also can't dock itself for charging, since the designers decided that the best way to achieve this would be to reverse the mowers onto the outdoor charging stand.

This means that they have to spin around (always turning the same way) and by coincidence, it looks rather as if it's the outside wheel that has come off worse and eventually failed.

So, repair is out of the question. De-rubbering the wheels is out of the question. Perhaps there's a DIY solution (let me know in the comments thread!) but the most obvious option is to replace the rubber treads.

In With the New Wheels

However, it seems that someone on the design team has realised their error with the wheels, and rubber treads aren't available, but nice, shiny, moulded plastic (with treads) wheels are.

They cost me around 25 EUR from the dealer, for a pair, and took a while to arrive -- they were permanently out of stock at the central stockists -- but when they did, they proved easy to remove and replace.

If you look at yours, you'll see that there are three torque type screws to remove, per wheel, which can be a bit tricky, due to the angles, but it can be achieved without dismantling the mower itself. This may not be the case for the original Husqvarna 305, but the Flymo 1200R and Gardena 40Li succumb to the direct approach easily!

The new wheels came without screws or washers, so you'll want to keep those and not throw them away when you dismantle the old wheels.

Besides the blades, and the occasional accident with the perimeter wire, this is the first 'major' part of the mower I've had to replace in 2 years, which makes it an immediate improvement over the old Wolf Garden manual motor-mower I used before, which suffered wheel-failure (traction belt) in the first year, and needed to be annually maintained by the local dealer to keep it working properly!

The next thing I expect to go will be the battery; I'm not sure what the lifespan of these is supposed to be, but we've already noticed extending charge cycles, and diminishing mowing times. Of course, without an actual measurement/download facility, that's anecdotal, but to be expected.

Still, being able to change the wheels myself, and as easily as changing the blades (despite having to shop-order them) removes another of my initial concerns about owning a robotic mower.

Tuesday, 8 October 2013

What Are the Differences Between the Major Robotic Lawn Mower Brands

Most robotic lawnmowers operate on the same basic principles with the same key features:

  • mulching blades (small amount of grass cut, drops onto the lawn)
  • powerful wheels (to deal with slopes)
  • sensors (to avoid obstacles)
  • guide wire (to keep within one or more zones)

However, within these principles there is scope for quite a lot of variation, and some of the variations serve to differentiate the models on offer.

Of course, as always, one of the biggest differentiating factors is price. Across the ranges, prices can triple, so it's worth knowing what you are (potentially) getting for your money.

Different Blades

Underneath any lawn mower, be it a Flymo hovering mower, or a Briggs and Stratton powered petrol guzzling traditional push around mower, there are one or more blades.

Traditional mowers are built to cut through long grass that has either been neglected over the off-season, or needs cutting every week (and only gets cut once a week) with the clippings being taken off to be disposed of.

Robotic mowers are designed for one purpose - to cut automatically and regularly, and drop the grass tips down onto the lawn to mulch it; automatically providing nutrition as well as keeping the lawn trim.


Most of the mowers on the market have multiple blades, held in place by a screw, which spin around at great speed, clipping the tips of the grass, and then chopping those tips into a fine dust.

Above right, are the blades for a Bosch Indego mower, which are long and thin.

To the left are the blades from a Gardena / Husqvarna, and Flymo mower, all of which seem to be either manufactured by Husqvarna in different liveries, or made under license.

Then, there are the single blade varieties, such as those used by RoboMow models, as pictured on the right.

So, which is the best?

Naturally, each manufacturer will have their reasons, but from the point of view of the mulching process, I have an idea that the loose blades might provide a better cutting action.

However, they are also more likely to snap (it's happened twice on my Gardena/Husqvarna) and fall off. I have a sneaking suspicion that the single piece blades are less likely to fail, but more likely to do damage should they come off.

Different Wheels

There are really only two choices for wheel arrangements - thee or four wheels - but again there is a surprising amount of variety across brands. Originally, Husqvarna went with a three wheel model, with the rear single wheel being smaller, and on a pivot.

This is very similar to the Flymo wheel arrangement, pictured on the left.

It has been replaced in more recent models with a version that has the smaller wheel at the front, like the Bosch Indego, and which, like the Bosch also enters the charging station front-first as opposed to back-first like the smaller Flymo models

Different Control Styles

All mowers need to have sensors to avoid hitting obstacles (like dogs, cats or trees!) and these are usually in the form of bumpers. Bumpers are reliable in a way that, for example, an ultrasound sensor might not be.

Next to the bumpers are different remote control styles - some mowers have a control pad that lets the owner steer the mower from zone to zone, while most just take themselves to a new zone by following a guide wire.

The guide wire is accompanied by a perimeter wire, which restricts the mower to the current zone. Many manufacturers also sell a kit to add new zones, so that the mower can be used on a greater area than originally installed.

Finally, some more recent models are starting to use GPS (Global Positioning System) antennas to help map out the space that needs to be mowed, and also to make sure that the whole area has been cut.

This last is important because, like some robotic vacuum cleaners, most of the models on the market tend to mow in a random fashion, over an extended period of time, and use this to make sure that the whole lawn has been cut.

Some of the more expensive models also have other cutting modes, so that they can be adapted to different shapes of lawn. So, if you have a lawn that is (a) large and (b) has many obstacles as well as (c) being an odd shape, it's probably worth spending a bit extra to get a more clever mower.

One last differentiating factor is the charging station. While most manufacturers have spotted that this needs to be weatherproof and located outside, some of the cheaper models still have an indoor charging station and require the mower to be carried or driven from the garage to the lawn.

Clearly, in the interests of automatic mowing, and ease of use, an outdoor charging station is the way to go.

Armed with this rundown of the various different features of automatic robotic lawn mowers, you should now be ready to choose from the models on the market, and join the rest of us who can sit back and watch whilst our lawns are carefully and immaculately mowed!

Thursday, 26 September 2013

The Robomow RL 555-HD Lawnmower : A Robotic Automatic Lawnmower with a Few Issues!

Firstly, a disclaimer : I don't actually own one of these, but have spent time gathering the opinions of others, and hopefully can point out a few of the glaring omissions in the design of the mower, whilst helping out anyone who owns one (or something similar) and is having issues with it.

What we have is a re-branded Husqvarna (marketed by Gardena on the continent, and Flymo, I believe, in the UK) and, for the record, I'm pretty happy with it.
The Robomow RL 555-HD

The first issue is that the 555 needs to be indoors in order to be charged. This doesn't make sense for something that ought to be automatic in every sense. In fact, I was hard pressed to find another robotic mower that has the same requirement.

Luckily, Robomow have fixed this design fault in other models, such as the RL2000 and the aptly named City 110 (it won't mow anything bigger than a 'city' lawn!)

The 555 has, instead, a remote control that is supposed to be used to drive it out of the garage and onto the lawn. That feels a bit like pushing an old fashioned lawnmower (sorry, traditional lawnmower) out onto the lawn, and not what you'd expect from a 21st century invention.

Once on the lawn, the 555 navigates using a perimeter wire. This is the preferred method of enclosing mowing zones, and used by Bosch, Flymo, Robomow, and others. Usually it works well, but when it doesn't it's usually because there's a break in the wire.

These can be hard to track down, and there's no real substitute for going along the wire (a pain if it's been dug in) and trying to find the fault. However, that's a problem shared by all the current market leaders.

A word of advice - first check that the connectors are still plugged in okay by unplugging and re-plugging them into the base unit. Then, if that fails, change the connectors (I've left about 20 inches of cable after the plugs just so I can do that!) just to be 100% sure it's the wire, and not the plugs.

The plugs are outdoors, so it could just be that they have become full of water, eaten by pests, or otherwise damaged or moved.

The mowing action is also the same as any other automatic robotic lawnmower in that they don't pick up after themselves. They're designed to be run frequently, clipping the ends off the grass, and letting it drop down onto the lawn, thereby fertilizing it (the mulching idea.)

Now, the Robomow 555 has two issues here.

The first is that it is heavy to take from the garage to the lawn, and so having it mow every day is going to become a problem over time. Secondly, there are issues with the Robomow and wet grass, according to an Amazon review. Apparently, it doesn't cope well with it.

This could be an issue, because mulching is best done when the grass is damp, according to one of my fellow mower-owners. But, since I don't own one, I can't comment further.

All in all, the main downfall of the 555 is that it can't be charged outside, which removes one of the central pillars of the buying decision : that it be convenient. To give them credit, the manufacturer has spotted this, and other models are self-charging, outside.

Wednesday, 11 September 2013

Installing the Perimeter Wire for your Automatic Robotic Lawnmower

One of the trickiest tasks when you first install your automatic robotic lawnmower is getting the perimeter wire right.In fact, there are usually two wires:

  • perimeter wire round the outside (stops the robot leaving the lawn)
  • guide wire (helps the robot get back to the charging base)

We'll deal with the guide wire in a later article, for now let's look at the perimeter wire. The easiest example is a rectangular lawn.

Placing the Perimeter Wire Around a Rectangular Lawn

Many lawns are basically rectangular - even our lawn, which has two zones (front and back) and an 'upper back' lawn, some swings, raised flower beds and a patio, is essentially rectangular.

The only concerns are:

  • having enough wire
  • what to do about corners

The first is easy enough - just measure the perimeter, and buy more wire if necessary! The second needs some explanation. The picture on the left shows my initial installation attempt, next to the patio.

Incorrect Perimeter Wire Placement
The blue line shows the wire, and you can assume that the area to the left and below the picture are out of bounds for the mower.

The red line shows the path that the mower consistently took. The result was that it would keep stopping with an "Outside mowing area" error!

In the manual, the instructions were quite clear to avoid sharp corners, but somehow I ignored this advice.

Clearly, you do need to follow it, so I adjusted the wire to look like the picture below.

Now, the robot doesn't exit the mowing area, and all is well. Of course, I had to buy extra clips because it's a more complex shape, but Husqvarna sells them in packs of 100, so although it was an extra expense, it wasn't insurmountable.

Correct Perimeter Wire Placement
Plus, it was cheaper than replacing the blades which were grinding themselves on the coping that runs around the edge of the lawn!

Another point to watch when laying the perimeter wire is the distance between the wire and the edge of the lawn.

The temptation is to get as close as possible to the edge, to avoid having to use a strimmer or edge cutter, but it's a false economy, as the robot needs space to turn, and not leaving enough space means that it will also exit the mowing area.

For those who have a raised edge, and are using that to limit the robot, that's fine, but it does cause wear and tear to the bumper.

Of course, if you are lucky enough to have a robot mower that uses ultrasound, that doesn't apply!

The Perimeter Wire and Obstacles

It is also possible to branch the perimeter wire out, and use it to go around an obstacle in the lawn (such as a valuable bush, or tree). The only thing to watch is that the wire is kept close to itself when it is doubled back (to return to the perimeter) so that the robot ignores it. Otherwise, it can get stuck in an area bounded by the outgoing wire, and the edge of the mowing area.

My preference was to build a small wall around things like shrubs and trees, because:

  • it would take a lot of wire to go round every obstacle
  • it increases the risk of problems with the wire breaking.

Again, following the instructions is paramount!

Setting Up The Perimeter Wire with Multiple Zones

Our lawn is essentially split into three parts, two are connected by a passageway, but the other is at the front of the house and not reachable by the robot mower automatically. We carry it between the back and front zones, manually!

The front zone is created by a perimeter wire that is taken off the main charging station, and runs completely around the lawn, bounding it.

At the back, the perimeter wire runs around the edge of the first zone, and then along the edge of the passageway, around the second zone, and back to the charging station.

The gap between the wires at the closest point of the passageway is less than a meter; this isn't ideal, as the robot sometimes doesn't quite make it through (in either direction) and therefore:

  • gets stuck in the second zone, or
  • never mows the second zone!

I'm still looking for the best solution for this, but I suspect I'll end up widening the passageway. I'll keep you posted...